Misunderstanding of replica watches

1. Wearing a sauna folding table, the behavior is completely wrong. No matter how deep the waterproofing is, the sauna cannot be used. Maybe the emergence of time will not be a problem. In fact, the movement was disrupted. Because the appearance of the clock is the reason for the different material decomposition coefficients, if you wear a folding table that is greater than or equal to the ambient temperature of 50 degrees, the table will produce a pressure difference. Under the action of air pressure, the air in the table will be at a temperature difference. Exhausted to the table. When the humidity is higher than the standard value, the steam with the bath temperature higher than the standard temperature will be exhausted in the air. Water vapor does not appear immediately on some chairs fake Rolex, but when the temperature exceeds the standard temperature at a low temperature on the table, the air on the glass will condense, forming water droplets or mist and steam heat, thereby accelerating the aging of the waterproof apron, The core cannot be protected.

2. Confirm the mirror water drop-sapphire crystal during condensation; this method is unscientific. Because mineral glass will condense a drop of water and some water droplets will be scattered on the sapphire, but the degree of wear is the same, so the mirror table of the material manufacturer should not be tested with water.

3. The quartz replica watch has replaced the battery, it is no longer waterproof, and the travel time is not accurate: this is incorrect. The equipment in the professional repair station is very perfect. For your battery, the professional technician will use the professional equipment to re-press, install the waterproof, and the stroke measurement error is within the normal value. Therefore, please replace the battery at a professional repair station.

4. Confirm the wear table with friction, soil, glass, etc. However, we do not recommend customers to use destructive behavior for testing. In addition, although high-tech ceramics are highly worn, they are fragile and are afraid of falling and violent influence.

The importance of good sealing of replica watches

The dial inside the needle and the needle mechanism, most of which have gears, are usually behind the wheels, or called “small center” wheels, depending on whether the movement is viewing or in the center of the disk in the center of the disk. The wheel will be defined. The partial eccentric movement of the movement, the wheels and gear shaft coils on the hub have flexibility.

This position is compact, loosens when the needle is felt, and is most susceptible to wear in this position. Especially for mechanical watches, due to frequent dialing, it is necessary to fausse rolex dial or adjust the calendar regularly, which will increase the wear of the wheel.

If it is loosely viewed from the dial, the “handless” watch may fail. The so-called “without hands” replica watch means that the clock is moving, the minute hand is not moving, and the time is “throwing” when it is not moving. Especially with calendars, calendars, clocks, jumping days, when the “load” movement will gradually expand, if the needle is lost, it is likely to appear “lost” problem, when watching slowly or simply walking fake watches, the minute hand does not Will move.

Allows the replica watches to achieve the same waterproof performance as the original

You can clearly see that there is no gap in the strap after cutting. It is an ultra-thick piece of pure natural rubber.

We are comparing a slightly inferior rubber strap. We can find that this strap is made of two thin pieces of rubber with a gap in the middle. This causes the rubber strap to be cold. In the environment, it will be more fragile and prone to cracks.

Here are the details of the bezel. This replica watch and the Sub’s bezel look similar but completely different. In terms of rotation, this outer ring rotates in both directions. The Sub is a unidirectional rotating outer ring. Therefore, the design also needs to fake Rolex be redesigned. However, such a two-way rotation will have a good advantage, that is, because the Sub has a card position, it will cause the bezel to loosen a little, but YMII will not have this situation at all.

The handlebar head is completely set according to the genuine design, and is set at the same time. Allows the fake watch to achieve the same waterproof as the original. Regarding the differences between the physical and the design drawings, you can compare them. The size of the design drawings is already very large. And it is a full-plane design drawing, and everyone can compare it to the original and see the difference.

The movement is equipped with a genuine ETA 2836-2 movement produced by the original Bao Yingnag. The default day difference is the water of the observatory. No need to re-calibrate, the durability is the same as the genuine INAG. This is a super high quality replica watches movement that no seller can provide.

Check the warranty period of the mechanical replica watches and repair warranty for half a year

Light illuminates the watch, and the coated luminescent material is mainly composed of a mixture of radium and zinc sulfide. The radium ray can stimulate the zinc-silver crystal light sleep. If the wearing body will be eight, nine o’clock radiation, there is a certain amount to the human body. s damage. Therefore, before going to bed replicas panerai relojes, it is best to bring a bright table and put it on the table.

Check the warranty period of the mechanical watch and maintenance warranty for half a year, after the warranty for three months LCD last month, the quartz clock is guaranteed, watching the clock for 14 days. From the date of collection. If the closure is found during the warranty period, this trip is inaccurate, free of charge replique montre, and is calculated during the warranty period.

We can watch the movement of any oil-filled dip tube inside without looking at it, expecting it to become omnipotent rather than expensive. (A few special watches are filled with oil and really sneak into the water, although we can use paperweight. No), it is no coincidence that we have to start with a large chunk of money at the beginning of this section because the butter in the watchmaking industry is often used. The oil of Swiss watches is crucial. The ball watch says: “The manufacturer usually mixes different oils to improve and improve their lubricity and thickness problems. In considering the thickness of the oil problem, it should be understood that the thickness can be used in the oil blending of the engine oil in the low temperature environment. Suitable for ideal lubrication in all temperature environments.

Modern oil replica panerai watches come from oil and consist of a hydrocarbon chain called paraffin. This significant difference in fat, oil molecules with carbon atoms and 15 to 20 fat molecules containing 20 to 25 carbon atoms should be part of the strong technical problem of the watch is what oil, but the basic principle of high speed and low torque is required to use light Low-speed, high-torque components with lubricants require heavy oil lubrication. In short, the former includes a trigger wheel, a wheel pivot trigger and teeth, while the latter includes a mainspring, the first and second transmissions